The Unit 9 Problem Set has five problems of four kinds. Each module below explores one kind, has you solve it, then gives you a new one to try. You choose how much help you get.
In the graphs and diagrams, charge is purple, current is blue, voltage is orange, resistance and inductance are green, energy is magenta, and times and phase are amber.
A metal detector rings an LC circuit, and nearby metal shifts its frequency. Model the circuit as a 0.500 mH coil and a 0.200 µF capacitor. At the capacitor holds 4.00 µC and the current is zero. Write the charge as a function of time and check that it satisfies the loop rule, then find the frequency, the largest current, the total energy, and the first time the current is largest.
On paper, draw the capacitor and the coil connected in a loop. Mark the charge on the capacitor plates at , and note that no current flows yet.
Once the capacitor starts to drain through the coil, can the current jump to its largest value right away?
At all the energy sits in the capacitor's electric field. The coil resists the current's growth, so the current builds over a quarter cycle while the capacitor drains, and the energy moves into the coil's magnetic field.
At the instant the capacitor's charge passes through zero, the current in the circuit is
Move through one full cycle. The graph shows the charge and the current, and the bars show where the energy is at that moment.
Move slowly through the first quarter cycle, then the rest.
The loop rule for a capacitor and a coil gives a second-order equation for the charge, the same form as a mass on a spring. A cosine solves it if the angular frequency fits, and differentiating the charge gives the current.
The total energy, , stays the same at every moment. The loop rule, the resonant frequency and the energy rows are on your Formula Sheet. In Part 2, you'll solve the metal detector.
A speaker crossover keeps high notes out of the woofer with a 1.50 mH inductor. To see how it sorts notes, connect the inductor alone across an amplifier output of 6.00 V rms. Find its reactance and the rms current for a 100 Hz bass note and a 5.00 kHz note, whether the current leads or lags, and the average power the inductor takes in.
On paper, sketch one cycle of the voltage across the inductor as a sine wave. Then sketch the current, remembering that the inductor's voltage is .
When the voltage is at its peak, is the current changing fastest or slowest?
The voltage is largest when the current changes fastest, which is when the current passes through zero. So the current peaks a quarter cycle after the voltage: it lags.
Raise the frequency from 100 Hz to 5.00 kHz with the same voltage. The current through the inductor
Change the frequency and switch between the inductor and a capacitor. The graph shows both reactances against frequency, with a marker at your setting.
Sweep from low to high frequency.
Each reactance is the ratio of peak voltage to peak current, like a resistance. An inductor's grows with frequency because a faster change needs a larger voltage, and a capacitor's shrinks because it has less time to fill.
For an inductor alone, the current lags by a quarter cycle, so the power factor is zero. The reactance rows are on your Formula Sheet. In Part 2, you'll solve the woofer inductor.
A guitar amp shapes its tone with a series RLC circuit: a 20.0 Ω resistor, a 10.0 mH coil and a 2.53 µF capacitor, driven by a 1.00 V rms signal. Find the resonant frequency, and at resonance the impedance, the rms current, the average power and the rms voltage across the coil alone. Then find the impedance, phase angle and power for a 500 Hz signal.
On paper, draw the three elements in series with the source. Then draw the phasors: the resistor's voltage along the current, the coil's a quarter turn ahead, the capacitor's a quarter turn behind.
The coil's and the capacitor's phasors point in opposite directions. What happens when they are the same length?
The source voltage is the arrow sum of the three. When the coil's and the capacitor's voltages are equal, they cancel, and the source voltage lines up with the current.
At resonance, the rms voltage across the coil alone is
Change the frequency. The phasor diagram shows the voltages, and the readouts show the impedance, current and phase.
Start at resonance, then move above and below it.
The resistor's voltage and the difference of the two reactive voltages are at right angles, so the Pythagorean theorem gives the impedance. At resonance the reactances cancel, the impedance is just the resistance, and the current peaks.
A positive phase angle means the current lags. The impedance, phase angle, resonance and power rows are on your Formula Sheet. In Part 2, you'll solve the tone circuit.
On its low setting, a 1,500 W hair dryer passes the outlet's current through a diode, which blocks every negative half-cycle. Write the 120 V rms outlet voltage as . Integrate to show that and find the peak voltage, then integrate to find the rms voltage on the low setting and the dryer's power there, treating its resistance as constant.
On paper, sketch two cycles of the outlet voltage. Then sketch its square, , below it.
Can ever be negative? What would you have to do to get one number that describes how strongly the voltage heats a resistor?
The voltage averages to zero over a cycle, but its square is never negative. Its average is half the peak squared, so the rms value is the peak divided by the square root of 2.
Over one full cycle of the 120 V rms outlet, the average of the voltage is
Choose how much of each half-cycle reaches the dryer. The shaded area is over the part that gets through, and the readouts give the rms voltage and the power.
Try each setting.
The rms value is exactly what its name says, done in reverse order: square the voltage, average it over one period, then take the square root. The identity turns the integral into one you can do.
A transformer uses rms values directly, and its voltage and current ratios run opposite ways. The rms and transformer rows are on your Formula Sheet. In Part 2, you'll solve the hair dryer.