The Unit 6 Problem Set has five problems of four kinds. Each module below explores one problem, has you solve it, then gives you a new one to try. You choose how much help you get.
In the diagrams, ⊙ means a field or force pointing out of the screen toward you, and ⊗ means one pointing into the screen.
Radiocarbon labs date ancient bones by counting carbon-14 atoms, and one step sorts carbon ions by mass. Singly charged carbon-12 ions () and carbon-14 ions () start at rest, accelerate through 5.00 kV, then enter a uniform 0.800 T field at right angles to their velocity. Find each ion's speed and the radius of its path, and how far apart they land after half a circle.
On paper, draw an ion entering a region where the field points out of the screen. Draw its velocity at the entrance, and use the right-hand rule to draw the force on it.
The force is perpendicular to the velocity. What does a force like that do to a moving object's path, and to its speed?
For a positive ion moving right through a field out of the screen, points down, so the ion curves down. The force stays perpendicular to the velocity at every point, so it always points to the center of a circle.
As the ion travels around its half circle in the field, its speed
Change the field and the accelerating voltage. Both isotopes travel half a circle, and the readouts show the speed at the start and end of the path.
Try a stronger field, then a higher voltage.
The electric field speeds the ion up, so energy gives its speed. The magnetic force only turns it, so Newton's second law with the centripetal acceleration gives the radius.
The force law, Newton's second law and the energy rows are on your Formula Sheet. In Part 2, you'll sort the carbon ions.
The buzz you feel from a phone or game controller can come from a small actuator built like a speaker: a coil sits in the gap of a ring magnet, where the field points straight out from the coil's axis in every direction. The coil has 40 turns of radius 4.00 mm, the field is 0.900 T, and the coil carries 0.100 A. The coil and the mass it shakes total 1.50 g. Find the total length of wire in the field, the force on the coil and its acceleration.
On paper, draw the coil from above as a circle, with the field arrows pointing outward from the center. Pick one small piece of wire at the top of the circle and one at the bottom, and draw the current's direction at each.
For each piece, which way does point?
With the current running clockwise as seen from above, at the top piece the current runs right and the field points up. At the bottom piece, the current runs left and the field points down. Both the current and the field reverse, so the cross product doesn't, and both forces point out of the screen.
The field at the top of the coil points the opposite way from the field at the bottom. The forces on those two pieces of wire
Move the piece of wire around the coil, and reverse the current. The symbol shows the force on that piece.
Move the piece all the way around, then reverse the current.
Every piece is perpendicular to the field, and every piece's force points the same way, so the forces add directly.
When the wire isn't perpendicular to the field, only the perpendicular part counts: . The force law is on your Formula Sheet. In Part 2, you'll work the actuator through.
A straight copper trace on a circuit board is 6.00 cm long and carries 2.00 A. Find the magnetic field it makes at a point 1.00 cm from its midpoint, in the plane of the board, by integrating the Biot-Savart law along the trace. Compare it with the field of an infinitely long wire at the same distance.
On paper, draw the trace along the x-axis with its midpoint at the origin, and point P a distance above the midpoint. Pick one small piece at position , and draw the line from it to P.
How far is the piece from P? What is the sine of the angle between the piece and that line?
The piece is from P, and the sine of the angle between and is . Every piece's field at P points the same way, out of the screen for current to the right, so the pieces add without components.
Which pieces of the trace add the most to the field at P?
Split the trace into more and more pieces. Each bar is one piece's field at P, and the sum appears below the chart.
Slide up to more pieces.
Write the field of one piece, then integrate along the trace.
The Biot-Savart law is on your Formula Sheet. The integral is a standard one: . In Part 2, you'll evaluate it for the trace.
In a wire carrying a rapidly alternating current, the current crowds toward the surface. Model the current density at one instant in a long wire of radius as , with a total current of 20.0 A. Find , then use Ampère's law to find the field at , at the surface, and at .
On paper, draw the wire's cross-section as a circle, shaded darker near the edge where the current crowds. Draw an Ampèrian circle of radius inside the wire, centered on the axis.
Which way does the field point along your circle, and how much current does the circle enclose?
By symmetry the field circles the axis with the same size all the way around, so . The circle encloses only the current inside it, and since the current isn't spread evenly, you integrate to find it.
Where inside the wire is the magnetic field strongest?
Grow the Ampèrian circle. The graph compares this wire's field with a wire of the same total current spread evenly.
Slide out to the surface at 2.00 mm, then beyond it.
Symmetry turns the left side into . The right side needs the current inside the circle, found by adding thin rings of area .
Outside the wire, the circle encloses all the current, and the field is the same as any long straight wire's. Two parallel wires each make that field at the other, which gives the force between them. Ampère's law is on your Formula Sheet. In Part 2, you'll work the crowded wire through.