The Unit 5 Problem Set has five problems of four kinds. Each module below explores one problem, has you solve it, then gives you a new one to try. You choose how much help you get.
A camera flash stores its energy in a capacitor. When you switch the flash on, a 300 V supply charges an empty capacitor through a resistor, and the ready light comes on at 290 V. Write the loop rule as a differential equation, solve it for the charge, and find how long you wait for the ready light.
On paper, draw the loop: the supply, the resistor and the capacitor in series. Mark the direction of the current and the capacitor's positive plate.
Walk around the loop in the direction of the current. Where does the potential rise, and where does it drop?
Going around in the direction of the current, the potential rises by across the supply, drops by across the resistor, and drops by across the capacitor. The loop rule says these add to zero at every instant.
The current starts at . As the capacitor fills, what does the current do?
Slide the time forward. The solid curve is the capacitor's voltage. The dashed line shows what would happen if the current stayed at its starting value.
Slide to 0.330 s, one time constant.
Write the current as the rate charge builds up on the capacitor, . The loop rule becomes a differential equation for . Separate the variables and integrate from the starting charge.
The loop rule and are on your Formula Sheet. In Part 2, you'll finish the integral for the camera flash.
When you switch off a stereo amplifier, its power-supply capacitor holds 35.0 V. A bleeder resistor connected across it drains the charge. Find the time constant, the voltage 10.0 s after switch-off, how long it takes to fall to 5.00 V, and the energy stored at switch-off.
On paper, sketch the capacitor's voltage against time after switch-off, starting from 35.0 V.
Does the voltage fall in a straight line? What sets how fast it falls?
The voltage falls by the same factor, , in every time constant : from 35.0 V to 12.9 V after one, and to 4.74 V after two. The curve flattens out and never quite reaches zero.
Now picture charging. You double the battery's emf in a charging RC circuit and keep the same resistor and capacitor. The capacitor reaches 63% of its final voltage
Change the emf, the resistance and the capacitance. The dot marks the moment the capacitor reaches 63.2% of its final voltage.
Start by doubling the emf from 6.00 V to 12.0 V.
Solving the loop rule, as in Solving the RC Equation, gives these curves. Only sets how fast they change.
To find a time, divide out the exponential and take a natural log. is on your Formula Sheet. In Part 2, you'll drain the amplifier.
A 12.0 V battery, a switch and are in series. After , the circuit splits into two branches: one is , and the other is an uncharged capacitor. Find the current in each branch just after the switch closes and long after. Then the switch opens again. Find the time constant with which the capacitor discharges.
On paper, draw the circuit with the switch closed. Label the current through , through and into the capacitor.
An uncharged capacitor has no voltage across it. For an instant, what does that make it look like to the rest of the circuit?
A capacitor's charge can't change in an instant, so neither can its voltage, . Just after the switch closes, this one is still uncharged, so it acts like a plain wire. Long after, its charge has stopped changing and no current flows into it, so its branch acts like a break.
Just after the switch closes, how much current flows into the capacitor?
Slide the time after the switch closes. The arrows grow and shrink with each branch's current.
Slide all the way down to 0, the instant the switch closes. Then slide all the way up.
At the two moments that matter, the capacitor can be swapped for something simpler.
Just after a switch moves, an uncharged capacitor acts like a wire and a charged one acts like a battery of its own voltage. Long after, its branch acts like a break. Then the rest is Ohm's law and Kirchhoff's rules from your Formula Sheet. When the capacitor discharges, its time constant uses the resistance the charge flows through. In Part 2, you'll work all three moments.
A spot welder joins two sheets of metal by discharging a 0.100 F capacitor bank, charged to 50.0 V, through the joint. Model the joint as a resistor. Find the time constant and the starting current. Then integrate the power in the joint to find the energy turned to heat, and find how long the current takes to fall to 1.00% of its starting value.
On paper, sketch the current against time, and on the same axes the power, , scaled so both start at the same height.
Squaring the current changes how fast the curve falls. Faster or slower?
The current falls as , so the power falls as , twice as fast. The energy turned to heat is the area under the power curve.
Suppose the joint's resistance were half as large, with the same capacitor and voltage. The total energy turned to heat would
Change the joint's resistance. The shaded area under the power curve is the energy turned to heat.
Try a smaller resistance and a larger one.
Square the current, multiply by the resistance, and integrate over the whole discharge.
The one half comes from the 2 in the exponent, and cancels. Power and stored energy are on your Formula Sheet. In Part 2, you'll work the welder through.