The Unit 4 Problem Set has five kinds of problems. Each module below explores one problem, has you solve it, then gives you a new one to try. You choose how much help you get.
As a laptop battery fills, its charger's current falls steadily from to zero over , so . How much charge flows in the first 25.0 min, and how much in all? The cable's power wire is copper, 1.00 mm in diameter, with free electrons per cubic meter. How fast do its electrons drift at the start?
On paper, sketch the current against time for the whole 50.0 min. Mark the halfway point in time.
Charge is current times time when the current is steady. What plays that role when the current changes?
The graph is a straight line. Since current is charge per second, each thin sliver under the line, , is the charge that passes in that moment. Adding the slivers gives the area under the curve.
In the first half of the time, does the charger deliver
Slide the time forward. The shaded area is the charge delivered so far.
Slide to 25.0 min, the halfway point in time.
Integrate the current to get the charge. For the drift speed, the same current has to squeeze through the wire's cross-section, carried by its free electrons.
Both equations are on your Formula Sheet. In Part 2, you'll work the laptop charger through.
A building's electrical system is grounded through a copper rod driven into the soil. The rod is long with radius . Current leaving the rod spreads straight out through the soil, which has resistivity . Find the soil's resistance from the rod's surface out to . Ignore the ends of the rod.
On paper, draw the rod from above, as a small circle, with the current spreading outward. Then draw one thin ring of soil a distance from the rod's center.
The current crosses that ring. How long is the path through it, and how big is the area it crosses?
The current crosses each thin shell the short way, through its thickness . The area it crosses is the shell's side, , which grows as grows. So doesn't apply to the whole volume of soil at once, but it does apply to one thin shell.
Split the soil from 8.00 mm out to 1.00 m into shells of equal thickness. Which shells add the most resistance?
Split the soil into more and thinner shells. Each bar is one shell's resistance, and the readout adds them up.
Add more shells and watch the sum.
Write the resistance of one thin shell with the area at that radius, then add every shell with an integral.
is on your Formula Sheet. Here the path is , and the area is the shell's side. In Part 2, you'll evaluate it.
A camping lantern runs on a battery pack with emf and internal resistance . One bulb, , is lit. Then you switch on a second, identical bulb in parallel with the first. Find the battery's current, its terminal voltage and the first bulb's power, before and after.
On paper, draw the battery as an ideal emf in series with a small resistor , inside a box. Then draw both bulbs across the box's terminals.
Which resistances share one current, and which share one voltage?
The bulbs share the terminal voltage, so they're in parallel. All the current from the battery also passes through , so is in series with the pair.
When the second bulb comes on, what happens to the first bulb?
Switch the second bulb on and off. Then change the battery's internal resistance and try again.
Switch on the second bulb.
Reduce the bulbs to one resistance and add in series to find the battery's current. The terminal voltage is what reaches the bulbs.
These equations are on your Formula Sheet. In Part 2, you'll work the lantern through.
A light sensor circuit is a voltage divider: a 12.0 V source with negligible internal resistance in series with and . You measure the voltage across , first with an old analog voltmeter of resistance 1.00 MΩ, then with a digital one of 10.0 MΩ. Find the true voltage and what each meter reads.
On paper, draw the divider. Then draw the voltmeter where it connects, across .
Once the meter is connected, what is it to the circuit?
A voltmeter is a large resistor. Once it's connected, it sits in parallel with , and that pair replaces in the divider.
Compared with the true voltage across , the old 1.00 MΩ meter reads
Change the meter's resistance. The bars compare the reading with the true voltage.
Raise the meter's resistance to 10.0 MΩ and beyond.
Combine the meter with in parallel, then solve the divider with that pair in place of .
The divider comes from series resistors and Ohm's law, both on your Formula Sheet. In Part 2, you'll work both meters through.
Three branches join a top junction A to a bottom junction B. The left branch has a battery and . The middle branch has only . The right branch has a battery and . Both batteries have their positive terminals toward A. Find the current in each branch, and say whether battery 2 is delivering energy or being charged.
On paper, draw the three branches. Try to combine any two resistors in series or in parallel.
Can you reduce this circuit to one resistance?
No two resistors share both ends with nothing else between them, because each outer resistor sits in a branch with a battery. Series and parallel rules can't reduce this one. Instead, pick a direction for each branch current. If you guess wrong, the current comes out negative, and nothing else in the solution changes.
Battery 2 has the smaller emf, 6.00 V against 12.0 V. What does it do?
Change battery 2's emf. The arrows show the actual direction and size of each branch current, and the readout shows how far A sits above B.
Raise battery 2's emf and watch the right branch.
Charge doesn't pile up at a junction, and walking around any loop brings you back to the potential you started at. Those two facts give three equations for three currents.
Both rules are on your Formula Sheet. Crossing a resistor in the direction of its current lowers the potential by , and crossing a battery from − to + raises it by . In Part 2, you'll solve the equations.